Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- en:berechnungen:einfache_berechnung [2024/10/25 17:01] – neelest
+++ en:berechnungen:einfache_berechnung [2025/07/03 13:33] (aktuell) – cschall
@@ Zeile 1: / Zeile 1: @@
 ======Regular calculation ======
-The content is currently being processed and will be made available shortly. Please be patient.
+===== Starting a calculation =====
+There are two ways to start the calculation \\
+  - With selection of the calculation and process settings
+  - Quick calculation with the last used calculation and process settings
 {{ :berechnungen:rex171_ber_009_en.png?nolink |}}
+The first selection opens a window in which the process parameters and the calculation settings can be changed. The settings are presented below.
+Confirming the //Calculate...// button starts the calculation and the calculation progress and report display appears.
+With the 2nd selection, the last known process and calculation settings are used and the progress and report display appears immediately.
 {{ :berechnungen:berechnungseinstellungen:rex171_ber_005_en.png?nolink |}}
-{{ :berechnungen:rex171_ber_001_en.png?nolink |}}
-{{ :berechnungen:berechnungseinstellungen:rex171_ber_004_en.png?nolink |}}
+The calculation log appears in the upper part of the progress and report display. The calculation process can be recognised by the sequence at the bottom of the window. \\
-{{ :berechnungen:rex171_ber_010_en.png?nolink |}}
+Here means: \\
+  * **Green**: Successful calculation
+  * **Orange**: Warning message
+  * **Red**: Error message
+By clicking on an orange or red field, the log jumps directly to the corresponding warning or error message.
+==== Process parameters ====
+See [[en:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter|Define process parameters]]
+==== Calculation settings ====
 {{ :berechnungen:rex171_ber_002_en.png?nolink |}}
+The calculation settings are divided into 4 sections:
+===1. Throughput ===
+see also [[en:berechnungen:durchsatz|Throughput]]
+Three basic settings are possible here \\
+    * **Melt dominated**: Standard setting, melt conveying dominates the throughput
+    * **Coupling solids conveying**: the [[en:berechnungen:feststofffoerderung|Solids conveying]] of the feed zone is also taken into account
+    * **Slot bushing**: the throughput is determined by the [[en:eingabe_der_zylinderdaten:eingabe_eines_nutbuchsenextruders|Grooved bush]] ([[en:berechnungen:nutbuchsenberechnung|Grooved bush calculation]]).
+If a grooved bush is defined, you can also select whether the calculation
+  * **Stiff feed** (default) or
+  * **limited speed orientated**
+and the conveying case differentiation can also be selected.
+You can also select whether the throughput calculation should take [[en:berechnungen:wandgleitende_materialien|Wall-slipping]] into account. In this case, corresponding [[en:materialdaten:rheologische_materialdaten|material data]] are required.
+For **screws with barrier zones**, there are two options for calculating the pressure throughput
+  * The **matrix model** based on network theory, standard
+  * Assumption of a **constant pressure gradient** between the solids and melt channel
+If a **barrier zone becomes plugged** (solids bed width y in the solids channel over 100% achieved by compressing the channel, **within** a barrier zone), the following options are available
+  * Continued **conventional melting**, in this case the the conventional melting continues in the solid channel. A disperse melting is assumed for the melt channel.
+If solid bed widths of more than 100% **outside** a barrier section occur, the melting calculation is cancelled with a warning message.
+It is also possible to select whether the message of an insufficient feed throughput through the hopper should be displayed or suppressed. It only makes sense to display the message if a hopper has been defined. Otherwise, a round hopper opening the size of the extruder's nominal diameter is assumed.
+===2. Melting ===
+see also [[en:berechnungen:aufschmelzverlauf|Melting]]
+For degassing screws only, three options can be selected:
+  * **till degassing section**: Standard, the melting calculation stops at the first degassing section
+  * **conventional melting after degassing section**: conventional melting also in/after the degassing section. However, if disperse melting has already been forced, for example by a shearing part before the degassing section, disperse melting will continue to be calculated.
+  * **disperse melting after the degassing section**: disperse melting in/after the degassing zone
+===3. Temperature ===
+see also [[en:berechnungen:temperaturverlauf|Temperature]]
+  * If //Iterate temperature// is **not** selected, the calculation is only calculated with an //initial temperature profile//. This is described by a linear progression of the temperature from the melting temperature ($T_G$ / $T_K$) at the front edge of the hopper to the specified final melt temperature (see [[en:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter|necessary process parameters]]) at the screw tip. For degassing extruders, the specified final melt temperature already applies to the start of the first degassing zone and remains constant thereafter. \\ If //Iteration of the final temperature// is selected, the calculated temperature profile is used iteratively for a new calculation of the entire process until a stationary state (no change in the final temperature) is reached. \\ Since the influence of the entered melt temperature on the throughput is only minor, the temperature iteration can remain deactivated, provided a reasonable melt temperature can be estimated.
+  * If an internal temperature control is defined, the calculation of the internal temperature control can be activated or deactivated.
+===4. Power ===
+See also [[en:berechnungen:leistung_und_schubspannungen|Power]]
+Three power models can be selected:
+  * Enthalpy
+  * Isothermal
+  * Non-isothermal
+==== Check ====
 {{ :berechnungen:berechnungseinstellungen:rex171_ber_003_en.png?nolink |}}
+The //Check// overview summarises which curves and parameters can be calculated (green tick) or cannot be calculated (exclamation mark). \\
+Click on the exclamation mark to display the reason why a curve or parameter cannot be calculated.
 ===Further topics===
   * [[en:berechnungen:einfache_berechnung|]]
+  * [[en:berechnungen:prozess_iterieren]]
   * [[en:berechnungen:durchsatz|]]
-  * [[en:berechnungen:einrieselverhalten|]]
   * [[en:berechnungen:druckverlauf|]]
   * [[en:berechnungen:aufschmelzverlauf|]]
   * [[en:berechnungen:temperaturverlauf|]]
   * [[en:berechnungen:leistung_und_schubspannungen|]]
+  * [[en:berechnungen:schergeschwindigkeit]]
   * [[en:berechnungen:verweilzeit|]]
   * [[en:berechnungen:verweilzeitverteilung|]]