≪ View Page

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
en:eingabe_der_schneckendaten:schneckenzonen [2025/05/05 10:24] – cschallen:eingabe_der_schneckendaten:schneckenzonen [2025/07/16 14:51] (aktuell) – cschall
Zeile 27: Zeile 27:
  
 Basically, the width of the channel results in Basically, the width of the channel results in
-$$b=t \cdot cos(\varphi) - e$$+$$b=\frac{t \cdot cos(\varphi) - i  \cdot e}{i}$$
 $$\text{with}$$ $$\text{with}$$
 $$tan(\varphi)=\frac{t}{\pi \cdot \overline{D}}$$ $$tan(\varphi)=\frac{t}{\pi \cdot \overline{D}}$$
 $$\text{and}$$ $$\text{and}$$
 $$\overline{D} = D-h$$ $$\overline{D} = D-h$$
-with the pitch $t$, the pitch angle $\varphi$, the flight width $e$, the nominal screw diameter $D$, the channel depth $h$ and the effective diameter $\overline{D}$. \\+with the pitch $t$, the pitch angle $\varphi$, the flight width $e$, the nominal screw diameter $D$, the channel depth $h$ ,the number of channels $i$ and the effective diameter $\overline{D}$. \\
 In the figure above, however, areas that reduce the channel cross-section are marked in red. As REX/PSI always calculates with a simplified rectangular channel, the reduction of the channel cross-section is taken into account by a reduced channel width: In the figure above, however, areas that reduce the channel cross-section are marked in red. As REX/PSI always calculates with a simplified rectangular channel, the reduction of the channel cross-section is taken into account by a reduced channel width:
 $$b_{effective}=\frac{b \cdot h-A_{radii,\gamma}}{h}$$ $$b_{effective}=\frac{b \cdot h-A_{radii,\gamma}}{h}$$
Zeile 48: Zeile 48:
 The calculation of the channel cross-section takes into account the actual channel width $b$, the effective channel width $b_{effective}$, the channel height $h$, the flight width $e$ and the screw clearance $\delta$. The channel volume is made up of 2 areas: The calculation of the channel cross-section takes into account the actual channel width $b$, the effective channel width $b_{effective}$, the channel height $h$, the flight width $e$ and the screw clearance $\delta$. The channel volume is made up of 2 areas:
  
-$$A_{ges.}=A_{Kanal}+A_\delta$$+$$A_{total}=A_{channel}+A_\delta$$
 $$\text{with}$$ $$\text{with}$$
 $$A_{channel} = b_{effective} \cdot h$$ $$A_{channel} = b_{effective} \cdot h$$
Zeile 56: Zeile 56:
 {{ :eingabe_der_schneckendaten:abb_kanalvolumen_en.svg?nolink&800 |}} {{ :eingabe_der_schneckendaten:abb_kanalvolumen_en.svg?nolink&800 |}}
  
-The duct volume is calculated by multiplying the duct cross-section by the unwound duct length $L_{duct}$:+The channel volume is calculated by multiplying the channel cross-section by the unwound channel length $L_{channel}$:
  
-$$V_{channel} = A_{ges.} \cdot L_{channel}$$+$$V_{channel} = A_{total} \cdot L_{channel}$$
 $$\text{with}$$ $$\text{with}$$
 $$L_{channel} = \frac{L_{zone}}{sin(\varphi)}$$ $$L_{channel} = \frac{L_{zone}}{sin(\varphi)}$$