≪ View Page

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
en:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter [2025/05/14 15:04] – [Pressure at the screw tip] cschallen:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter [2025/06/27 13:13] (aktuell) – [Disperse melting at] cschall
Zeile 9: Zeile 9:
       * **Required parameters:** These values must be specified by the user as they are essential for the calculation.       * **Required parameters:** These values must be specified by the user as they are essential for the calculation.
       * **Optional parameters:** These values can be specified by the user, but are not mandatory. If these values are not entered, they are calculated automatically by the software. An example of this are parameters such as the location of the melt pool formation (OSW).       * **Optional parameters:** These values can be specified by the user, but are not mandatory. If these values are not entered, they are calculated automatically by the software. An example of this are parameters such as the location of the melt pool formation (OSW).
-      * **PSI only**: Inputs for cycle time calculation+      * **PSI only**: Inputs for [[..:berechnungen:zykluszeitberechnung|cycle time calculation]] 
       * **PSI only**: Inputs for calculating the closing time of the non-return valve       * **PSI only**: Inputs for calculating the closing time of the non-return valve
  
Zeile 47: Zeile 47:
  
  
-**Note:** The selection of the options //mould// and //mould characteristic// is only available in REX.  +**Note:** The selection of the options //Die// and //Die characteristic// is only available in REX.  
-====Pressure at the front edge of the hopper====+====Pressure at the hopper / material inlet====
  
-In addition to the pressure at the screw tip, the pressure at the front edge of the hopper must also be specified. This is normally 1 bar and therefore ambient pressure. However, higher pressures can also be specified; this is particularly relevant for melt extruders. The pressure at the front edge of the hopper may be higher than the pressure at the screw tip.+In addition to the pressure at the screw tip, the pressure at the hopper must also be specified. This is normally 1 bar and therefore ambient pressure. However, higher pressures can also be specified; this is particularly relevant for melt extruders. The pressure at the hopper may be higher than the pressure at the screw tip.
  
 ==== Melt temperature ==== ==== Melt temperature ====
Zeile 57: Zeile 57:
 The entered melt temperature therefore has an influence on the throughput calculation. However, the mass temperature can be iterated as part of the [[en:berechnungen:einfache_berechnung|calculation_settings]]. In this case, the input is required as an initial estimated value, but has no influence on the calculated throughput. The entered melt temperature therefore has an influence on the throughput calculation. However, the mass temperature can be iterated as part of the [[en:berechnungen:einfache_berechnung|calculation_settings]]. In this case, the input is required as an initial estimated value, but has no influence on the calculated throughput.
  
-The value therefore has an influence on the throughput calculation, but not indirectly on the temperature calculation. The temperature at the screw tip is **calculated** depending on the calculated throughput and **does not** correspond to the entered value.+The value therefore has an influence on the throughput calculation, but not on the temperature calculation. The temperature at the screw tip is **calculated** depending on the calculated throughput and **does not** correspond to the entered value.
  
-==== Raw material inlet temperature ====+==== Raw material temperature ====
  
-The raw material inlet temperature corresponds to the temperature at which the plastic is fed into the extruder/injection moulding machine. The temperature normally corresponds to the room temperature or the outlet temperature from a pellet dryer. \\ If a temperature above the melting temperature ($T_K/T_G$) is entered, the system is regarded as a melt extruder and no melting and melting calculation takes place.+The raw material temperature corresponds to the temperature at which the plastic is fed into the extruder/injection moulding machine. The temperature normally corresponds to the room temperature or the outlet temperature from a pellet dryer. \\ If a temperature above the melting temperature ($T_K/T_G$) is entered, the system is regarded as a melt extruder and no melting and melting calculation takes place.
 ===== Optional entries ===== ===== Optional entries =====
  
Zeile 68: Zeile 68:
 {{ :eingabe_der_verfahrensparameter:rex180_verf_en_002.png?nolink |}} {{ :eingabe_der_verfahrensparameter:rex180_verf_en_002.png?nolink |}}
  
-==== Location of the melt vortex formation ====+==== Location of the melt pool formation ====
  
-The location of the melt vortex formation can be specified. In this case, the melting and temperature calculation starts from the specified location. +The location of melt pool formation can be specified and is assigned to the start of the next calculation interval following the defined location. In this case, the melting and temperature calculations begin from the corresponding interval. 
-==== Disperse melting from ====+==== Disperse melting at====
  
 REX can calculate the [[en:berechnungen:aufschmelzverlauf|melting]] in the conventional way (Maddok model) or using a disperse melting model. Dispersive melting always starts with shear and mixing elements as well as wave zones. The change from the conventional melting model to the disperse melting model can be set to an **earlier** point using the optional input made possible here. REX can calculate the [[en:berechnungen:aufschmelzverlauf|melting]] in the conventional way (Maddok model) or using a disperse melting model. Dispersive melting always starts with shear and mixing elements as well as wave zones. The change from the conventional melting model to the disperse melting model can be set to an **earlier** point using the optional input made possible here.
-==== Throughput (at a specified speed) ==== 
  
-If a circumferential speed or a screw speed is specified, a throughput can also be specified here as an option. This skips the throughput calculation and the entered value is used. +==== Start Temperatur ====
-====Kennlinienfeld====+
  
-Clicking on the ‘Characteristic curve field’ button opens a new window.+As an additional optional input parameter, the starting temperature can be specified. This temperature corresponds to the temperature of the melt vertex at the location where the melt vertex is formed and represents the temperature at which the [[en:berechnungen:temperaturverlauf|Temperature calculation]] begins. 
 +==== Throughput (with given screw speed) ==== 
 + 
 +If a peripheral velocity or a screw speed is specified, a throughput can also be specified here as an option. This skips the throughput calculation and the entered value is used. 
 +====Characteristic field==== 
 + 
 +Clicking on the ‘Characteristic field’ button opens a new window.
  
 {{ :eingabe_der_verfahrensparameter:rex171_verf_en_003.png?nolink |}} {{ :eingabe_der_verfahrensparameter:rex171_verf_en_003.png?nolink |}}
  
-The characteristic curve field calculation can be activated here. Three pressures and three speeds are entered. In a process calculation, the throughput is calculated for each combination of pressures and speeds (thus for 9 operating points) so that the influence of speed and back pressure can be displayed in a diagram (see  [[en:grafische_darstellung_der_ergebnisse:kennlinienfeld|Graphical representation of the characteristic_curve_field]]).+The characteristic field calculation can be activated here. Three pressures and three speeds are entered. In a process calculation, the throughput is calculated for each combination of pressures and speeds (thus for 9 operating points) so that the influence of speed and back pressure can be displayed in a diagram (see  [[en:grafische_darstellung_der_ergebnisse:kennlinienfeld|Graphical representation of the characteristic_curve_field]]).
 ===== Cycle time calculation (PSI) ===== ===== Cycle time calculation (PSI) =====
  
 The cycle time calculation is treated separately The cycle time calculation is treated separately
  
-  *  cycle time calculation+  *  [[en:berechnungen:zykluszeitberechnung|]]
  
 ===== Inputs for calculating the closing time of the non-return valve ===== ===== Inputs for calculating the closing time of the non-return valve =====
  
-The 3 inputs are only used to calculate the closing time of the ring non-return valve.+{{ :eingabe_der_verfahrensparameter:psi160_verf_en_002.png?nolink |}} 
 + 
 +The 3 inputs are only used to calculate the closing time of the non-return valve.
  
-  * The injection pressure must be specified. The injection pressure is one of the forces that presses the locking ring against the locking tip. A [[en:eingabe_eines_werkzeugs:eingabe_eines_werkzeugs_psi|tool/nozzle_backpressure]] is also required as a counterpart to the injection pressure.+  * The injection pressure must be specified. The injection pressure is one of the forces that presses the closing ring against the pressure ring. A [[en:eingabe_eines_werkzeugs:eingabe_eines_werkzeugs_psi|nozzle and die]] is also required as a counterpart to the injection pressure.
   * Holding pressure   * Holding pressure
   * Holding pressure time   * Holding pressure time
  
 The holding pressure and holding pressure time are not absolutely necessary. They are only required if the locking ring of the ring non-return valve closes after the injection phase and therefore within the holding pressure phase. This is not a sensible operating point. The holding pressure and holding pressure time are not absolutely necessary. They are only required if the locking ring of the ring non-return valve closes after the injection phase and therefore within the holding pressure phase. This is not a sensible operating point.